Tab Notching Machine

Tab Notching Machine parad Battery Electrode Processing

Say SZO-DC350 et manproproseso na saray electrode sheet parad tab notching. Say sheet et ipaway ed material roll, i-align antis ya ipakan, insan ipawit ed knife mold pian putoten. Saray T-shaped tan straight tab designs et nilista parad makina, ya say tab pitch tan feed settings et nayarin i-adjust unong ed nakaukolan ya format na electrode.

Say sankatageyan ya kalapar na pakanen et 350 mm, tan say sankatageyan ya lugar na panagproseso et 340 × 300 mm. Say nilista ya kapeles na panagproseso et 20-30 reps/min. Say kapeles na pangipakan tan say kundang na pangipakan et nayarin i-adjust legan na operasyon, ya walay espisipikon inkasusto na pangipakan ya 0.1 mm o mas abeba ni.

Antis ya onsabi so sheet ed seksion na panagputot, nengnengen na alignment sensor so posisyon to. Say nibaga ya inkasusto na panag-align et ±0.3 mm. Say panagpakan et gagawaen na servo-driven platform, bangta say knife mold et nayarin i-adjust manlapud arap, beneg tan angular ya direksion.

Istruktura na Makina

Say SZO-DC350 et tugyopen na pigaran working sections imbes ya saksakey ya cutting unit.

Discharge unit
Say air-lift shaft so uusaren ed discharge section. Say baras et walay sukat to parad pangiposisyon na materyales, tan say mekanismo na pangipaway et kaiba so automatikon pakalikna. Nayarin i-set so delay timer unong ed nakaukolan ya karukey na sheet.

Mekanismo na panag-align
Say electrode sheet et ondalan ed alignment section antis ya onloob ed feeding platform. Say precision alignment sensor so uusaren pian nanengneng so posisyon na sheet. Say nibaga ya inkasusto na panag-align et ±0.3 mm.

Seksion na panagpakan tan panagmaneho
Say feeding platform et servo-driven. Duaran cylinder pressing plates so akapuesto ed arap tan beneg na processing section pian naala so sheet legan na pangipapakan tan panagputot.

Seksion na molde na kutsilyo
Say seksion na panagputot et manguusar na maples ya onkikiwas a silindro- ya molde na kutsilyo. Say posisyon na mold et nayarin i-adjust ed arap, beneg tan angular ya direksion. Say presyon na panagputot et na-adjust na kuryente.

Say balangkas tan kontrol na makina
Say manunan istruktura et manguusar na anemiran giya tan duaran servo system. Say pangi-adjust na pressure et nakontrol panamegley na machine control system. Say kagawaan et nayarin paandaren ed automatiko odino manual a paraan.

Panangasikaso na basura
Kayari na panagputot, say basura et ibiig ed naproseso lan materyales tan nakolekta ed seksion ya panag-asikaso na basura. Say detalye na makina et mangilista met na automatikon panagbiig tan panag-recycle ya kagawaan.

Panguman na conveyor
Say conveyor section et manguusar na dakel a baras parad pangiposisyon tan sakey a circulating transmission system. Walay duaran paraan na panag-adjust na makina parad tension na conveyor belt.

Teknikal iran Parametro

Saray Kakaukolanen ed Kaliberliber

● Temperatura na kaliberliber: 0-40 degree

● Relatibon danum: 20-90% RH

● Power supply: single-phase 220 V, 50 Hz

● Panguman-uman na boltahe: ±10%

● Proteksion ed dalin:<4 Ω

● Compressed air: 0.4–0.8 MPa

● Vacuum source: 20 L/min, -40 anggad -55 KPa

● Say pasen ya pangipaalageyan et nepeg ya anggapoy makaderal, makapaputok odino arum nin agmanepeg iran gas tan likido.

Saray Kakaukolanen ed Panag-instalar tan Panuporta

Say kustomer so responsable ed pangiparaan na nakaukolan iran koneksion na kuryente tan gas ya asingger ed posisyon na pangipuesto na kagawaan. Saray electrode sheet et nakaukolan met parad panag-debug na kagawaan, kaiba iray nakaukolan ya operator, maintenance personnel tan teknisyan.

Kayari na pangiter, say kustomer so mangasikaso ed pangiposisyon na kagawaan diad pasen. Say pangipuesto tan pangi-commission et gagawaen na supplier unong ed saray kakaukolanen na kagawaan.

Saray Kaso na Aplikasyon

Kasosyo na Kompanya

Mabetbet ya Itepet

Antoy kabaleg na electrode sheet ya sarag na SZO-DC350?

Say sankatageyan ya kalapar na pakanen et 350 mm, tan say sankatageyan ya lugar na panagproseso et 340 × 300 mm. Say aktual ya pangiletneg et mandedepende ed format na electrode tan say mold na kutsilyo ya uusaren.

Antoy kapeles na panagproseso na sayan makinan man-notch na tab?

Say nilista ya kapeles na panagproseso et 20-30 reps/min. Say kapeles na pangipakan tan say kundang na pangipakan et nayarin i-adjust panamegley na saray setting na makina.

Panon ya nakontrol so inka-align na electrode sheet?

Walay alignment sensor ya akapuesto antis na feeding platform. Say nibaga ya inkasusto na panag-align et ±0.3 mm, bangta say inkasusto na feed step et 0.1 mm o mas abeba ni.

Nayarin naproseso so nanduruman kurti na tab?

Say detalye na makina et mangilista na T-shaped tan diretso iran desinyo na tab. Say tab pitch tan saray misiglaotan ya setting na panagproseso et nayarin i-adjust parad nanduruman pankaukolan na electrode.

Anton klase na kutsilyo so uusaren na makina?

Say SZO-DC350 et manguusar na maples ya onkikiwas a silindro- ya molde na kutsilyo. Say posisyon na mold et nayarin i-adjust manlapud arap, beneg tan angular ya direksion, tan say cutting pressure et nayarin i-adjust panamegley na kuryente.

Susuportaan kasi na makina so automatikon operasyon?

On. Parehon akalista ed saray detalye na kagawaan so automatic tan manual ya paraan na panag-operate.

Anto ran utilities so nakaukolan ed pasen na pangi-install?

Saray estandarten kakaukolanen et kaiba so single-phase 220 V power, compressed air ed 0.4-0.8 MPa tan sakey a vacuum source ya walay flow rate ya 20 L/min. Say kaliberliber na pangipaalagey et nepeg met ya makaabot ed nibaga ya temperatura, humidity tan grounding ya kakaukolanen.

Sarag kasi ya nengnengen so makina parad sakey ya espisipikon format na electrode antis ya gawaen?

On. Saray sukat na electrode, kurti na tab, saray setting na feed tan saray kakaukolanen ed knife mold et nepeg ya kumpirmaen antis na produksyon no say materyales et duma ed estandarten setup. Saray electrode sheet et nakaukolan met parad panag-debug na kagawaan legan ya mangi-install.